La Pavoni Coffeemaker P03 User Manual

P03 / P06 / P09  
®
 
INTRODUCTION  
Dear Customer,  
Thank you for choosing our product.  
This machine, thanks to its reliability, will be able to win your preference also  
for other products in our range.  
Each dealer will be able to refer you to the nearest Service Centre.  
Notwithstanding the ease of use of the machine, in order to get the best  
results it is important to thoroughly read this booklet and follow all  
instructions before starting the machine.  
GENERAL INFORMATION  
The machine is suitable for preparing hot drinks, obtained by mixing hot  
water and granulated soluble products. The body of the machine is designed  
for indoor use only.  
Any service or repair work, with the exception of cleaning and normal  
maintenance, shall be carried out by an authorised Service Centre.  
To make reading of the manual easier, important information, which must be  
observed for the safeguard of the user and for the prevention of accidents,  
will be shown in bold and in some cases indicated by the following symbols:  
GENERIC HAZARD: it indicates important rules to be observed  
in order to avoid hazards to the user.  
ELECTROCUTION HAZARD: it indicates important information  
to be followed in order to avoid risks resulting from electric  
power  
The machine was conceived for use by adult persons only, who have their  
psycho-physical faculties unaltered. It is not suitable for use by children.  
 
IMPORTANT PRECAUTIONS  
When using electric material it is important to ensure the appropriate  
precautions are adopted in order to avoid electric shock, accidents  
and damage to persons and things.  
SAFETY REGULATIONS  
Make sure to implement all necessary precautions to avoid contact of the  
machine with liquids. Liquids can seep inside the machine and cause short-  
circuits or energise external parts of the machine.  
Thoroughly read all information contained in this manual and in any  
other attachment included in the packing.  
INTENDED USE OF THE MACHINE  
The machine is intended for adult persons informed on its operation, to be  
used in a sensible, conscious and careful manner (should the machine be used  
by other persons, we recommend to make this booklet available to them).  
It is intended for indoor use only.  
Ensure that the power supply voltage indicated on the data plate of the  
machine is compatible with the one from your power supply outlet.  
Take special care while using the machine in the presence of children.  
Verify that the main switch of the machine is not pressed before  
plugging or unplugging the power supply plug.  
Unplug the power supply plug from the power outlet and wait for the  
machine to cool down before starting any maintenance or cleaning  
operations.  
The machine is intended exclusively for dispensing hot drinks through the use  
of suitable granulated soluble products.  
Do not make any changes, and do not use the machine improperly or for a  
purpose different from the one for which it was designed.  
Do not use the machine when one or more components are damaged or  
missing (power supply cable, plug, switches, etc.). Get the machine to be  
checked or repaired at the nearest service centre.  
The use of accessories that are not recommended by the manufacturer  
can cause damage to persons or things.  
Do not immerse the machine in any kind of liquid; do not clean it with  
any strong detergents. It is sufficient to use a soft cloth soaked in  
warm water.  
To avoid short-circuits and/or electric shocks keep away from the  
machine liquids that may accidentally be spilled over the machine.  
INSTALLATION  
After opening the packing ensure that the machine is intact and check that all  
of the main parts are included (refer to the figures in the following pages).  
Plastic bags, polystyrene, nails etc. are potential sources of danger, therefore  
they must not be left unattended or within the reach of children.  
The machine must be positioned on a level, solid and stable surface, away from  
heat sources. Ensure a free space at the sides and at the back of the machine  
of at least 20 cm.  
There must be sufficient free space to allow the operator to have access  
to the machine in the event of malfunctions.  
In case of doubt or should the instructions in this manual not be clear enough, do  
not hesitate to ask for clarification from the supplier, an authorised service centre  
or directly from the manufacturer.  
Choose a hygienic and well lit room with an easy to access power outlet.  
Check that the power supply voltage of the machine  
is the same as the one of the power supply outlet.  
The power supply outlet must be conforming to the plug of  
the machine, sized to meet the characteristics indicated  
on the data plate of the machine and connected to an  
efficient earth circuit.  
4
- 3 -  
 
Check that the power supply cable is not damaged or defective. If  
there is a problem, do not use the machine under any  
circumstances. The power supply cable must be replaced by the  
manufacturer or by one of its service centres.  
CLEANING  
Before starting any cleaning on the machine, ensure that it is switched off  
and that the plug is unplugged.  
Wait several minutes to allow the components to cool down.  
Do not insert any objects in the holes of the machine.  
Pay attention to the position of the cable during installation, it must  
not be:  
REPAIRS AND MAINTENANCE  
-
-
-
-
-
-
-
a hindrance to persons or things  
crushed, pressed or placed on sharp surfaces  
bent forcefully  
In the event of failures, defects, suspected defects or if the  
machine is dropped, immediately unplug the plug from the power  
outlet. Never start a defective machine.  
Only the Authorised Service Centre or the Manufacturer can  
make repairs.  
placed near hot surfaces  
immersed, or placed near water or other liquids  
wound around itself when the machine is in operation  
tampered with.  
DANGER ASPECTS  
It is important to ensure that no children can touch the machine!  
The machine can be dangerous for children and must be made  
inaccessible to them. If not used or if left unattended, it must  
be deactivated.  
Do not leave any materials used for packing the machine within  
the reach of children.  
Do not insert any objects through the machine openings (Danger!  
Electric current!).  
Do not touch the plug and the cable while the machine is in  
operation; do not unplug by pulling the cable.  
The parts near the dispensing zone can be very hot. Caution!  
Risk of burns from contact.  
In the event of repairs that are not well made, we decline all  
responsibility for any damage.  
DISPOSAL  
The directive WEEE (Waste Electrical and Electronic  
Equipment) indicates that electrical and electronic  
products must be disposed of separately from normal  
urban waste and similar. The aim is to send the waste to  
authorised waste disposal centres, for the purpose of  
promoting ways of recovering or recycling.  
The directive includes also the accessories, the power  
supply cables, etc  
To correctly dispose of these products, follow the regulations provided by  
the municipal authority and/or request further information from your  
dealer when purchasing a new product.  
5
6
 
OPERATING INSTRUCTIONS  
CONTROL PANEL  
F03  
F06  
F09  
1 Drip tray  
The figure shows the F09,  
which has 3 canisters. The  
F06 and F03 versions differ  
from this in number of  
canisters, respectively 2 and  
1
2 Cup support grille  
3 Canister of product A  
3 Canister of product B  
3 Canister of product C  
4 Door  
5 Water level sensor  
6 Water tank  
7 Main switch  
8 Control panel  
7
8
 
PRELIMINARY OPERATIONS  
Before inserting the plug and switching the machine on, remove the water  
tank, thoroughly rinse it and fill it with fresh water.  
As indicated in the figures of the previous page, the machines have 2  
dispensing buttons for each granulated product:  
-
-
Large cup: long dose  
Small cup: short dose  
Replace the tank, ensuring that the level sensor is immersed in the water.  
Pour in the tank only fresh drinking still water. Hot water or other liquids  
can damage the machine.  
Do not start the machine without water; for correct dispensing, the softener  
filter located at the end of the intake tube must be immersed completely.  
In addition, they have a rinse button for each mixer unit installed.  
The name assigned to the buttons in the figure (e.g. A1-A2), indicates the  
name of the controlled mixer unit, A is the first one from the left.  
YES  
LOADING THE GRANULATED PRODUCT  
IMPORTANT NOTICE:  
The products dispensed by the machine with the appropriate mixing and  
associations to the control panel are preset at the factory.  
It is not possible to dispense different products from the ones for which the  
machine is manufactured.  
For machines equipped with more than one canister, make sure that each  
product is located in the correct position.  
Remove the canister, rinse it and dry it thoroughly. Pour the granulated  
powder product, then fit the lid and replace the canister in its place. Verify  
that the pin protruding from the base is inserted into the corresponding hole  
of the machine.  
9
 
STARTING THE MACHINE  
N.B.: the machine requires little time for heating, if not  
used in the immediate future, it is advisable to switch it off.  
For correct dispensing, it  
is important that the  
product  
inside  
the  
canister never falls below  
this level.  
After completing the preliminary operations, place a large enough container in  
the drink dispensing point.  
NOTE: the different configurations of the machine allow one or more  
dispensing points.  
Make sure the main switch is set to the position “0”  
Insert the plug in the power outlet.  
It is possible to understand if your model dispenses drinks in a single  
point by the pattern on the grille, which has a sector with concentric  
circles. On the contrary, the product will be dispensed under its own  
mixer body.  
It is important for the power outlet to  
be compatible with the plug of the  
machine and provided with the earth  
connection pin.  
Start the machine by pressing the main switch. After approximately 10  
seconds, press the rinse button “L” to fill the machine internal circuit (if the  
dispensing points are not grouped, make sure to press the rinse button  
corresponding to the mixer body where the contained was placed).  
Water coming out of the mixer spout means that the circuit is full.  
Dispense at least two cups of water (it may be necessary to press the button  
several times).  
Never operate the machine without first filling the water circuit, not to  
damage the heating element. If the water level in the tank is too low and  
the water level sensor is not immersed, this will disable the electronic  
card  
.
11  
12  
 
Pay attention now, the display will indicate the message “READY -  
SEL.PRODUCT“ and at this point it will be possible to dispense the desired  
drink by pressing the corresponding button.  
Periodically wash the water tank and replace the water.  
Using a soft cloth damp with warm water, clean the outside of the softener  
filter and the intake tube to which it is fitted.  
INSTRUCTIONS FOR ROUTINE CLEANING  
In order to keep the machine efficient and ensure a long lasting  
duration, it is sufficient to take some simple precautions.  
N.B.: The softener filter operates correctly up to 35 litres of water,  
after which it must be replaced.  
The machine will indicate on the display the end of the recommended filter  
autonomy; after replacing the filter to reset the message, press and keep  
pressed the rinse button of mixer A.  
When switching the machine on, every now and then during the  
course of the day and before switching it off, clean the mixer  
by pressing the rinse button.  
Clean the inside of the canister compartments.  
Under no circumstances proceed by disassembling the machine.  
Every day, at the end of the day,  
disassemble the parts that compose  
the mixer unit (‘X’, ‘Y’, ‘Z’, ‘K’, ‘J’ and  
the internal plastic impeller ‘W’) and  
therefore wash them with hot water.  
DESCALING  
Periodically it may be useful to descale the circuit using a specific product for  
coffee machines, of the NON TOXIC type. Normally available in major  
stores.  
Warning! Under no circumstances use vinegar for descaling.  
After using the product, thoroughly wash the water tank and rinse the circuit  
by dispensing water only continuously, using a few times the maximum capacity  
of the water tank.  
The figure is only an example;  
the shape of the elements may  
vary according to the product  
to be mixed.  
13  
14  
 
TROUBLE-SHOOTING  
The machine dispenses too little water:  
replace the resin filter fitted on the water intake tube and located  
inside the water tank.  
The machine dispenses one drink and then stops:  
check the water level in the tank and if necessary refill it or verify  
that the shut-off valve is open.  
The powder is not dispensed:  
check that the product canister is correctly inserted in its seat  
and/or there is sufficient product.  
There is a water leak between component Z and its connection P in the  
machine:  
check that the component Z is inserted correctly.  
When pressing buttons A or B the product is not dispensed:  
the operating temperature has not been reached yet, wait a few  
minutes.  
15  
 

Lexmark All in One Printer X4270 Series User Manual
LG Electronics Refrigerator LRBC22522 User Manual
Linear Automobile Electronics AK 21 User Manual
Linksys Network Card LKG0F755E User Manual
Logitech Speaker System Z120 User Manual
Marantz Home Theater System PM 17SA User Manual
Melissa Hot Beverage Maker 245052 User Manual
Metra Electronics eBook Reader 99 7407 User Manual
Microsoft Tablet 7XR 00001 User Manual
Midland Radio Camcorder XTC 200 User Manual